Getting video is not the same as controlling your camera.
DJI checks 4K monitoring, HD monitoring, PTP camera control and CEC mirror control separately. Read the four columns for your exact body before choosing cables or promising a remote-control workflow.
Quick answer
Most cameras in DJI's 1 September 2026 SDR Transmission 2 compatibility list have 4K and 1080p/1080i monitoring marks, but control varies by model. Sony FX3 has all four marks; FX30 lacks a CEC mark, and FX6 has no PTP or CEC mark. A camera can send a clean HDMI picture while the Ronin app still has no remote ISO, shutter or aperture controls. Check the exact row, the correct cable path and the camera's USB/HDMI settings before a shoot.
“Compatible” describes four different capabilities
DJI's Camera Compatibility List is not a single yes-or-no badge. It has two video-monitoring columns and two control columns. The distinction matters whenever a director only needs a feed, while a camera operator expects to change exposure from the receiving end. Those are different promises and, in the case of PTP, different camera-to-transmitter connections.
A checkmark is evidence for that column in DJI's current document. A blank is not marked in that document; it is not a universal statement that the camera hardware can never perform the function. Firmware, camera settings and DJI's list may change. Use the full DJI SDR Transmission 2 Camera Compatibility List for the current row and recheck it before buying for a critical shoot.
Compatible camera does not mean every function is supported. A body with 4K and HD marks but blank PTP and CEC cells remains a documented video source. Do not sell it as a remote-exposure-control setup on the strength of the video marks alone.
Why HDMI picture does not automatically enable ISO control
For ordinary monitoring, the camera sends a supported video output to the SDR Transmission 2 unit in TX mode. The wireless link carries that feed to an RX and then to a display or a supported mobile viewing workflow. HDMI can also be the connection used for CEC Mirror Control on models DJI has marked for it, but a working picture alone is not evidence that the mirror-control function is available or enabled.
PTP stands for Picture Transfer Protocol. In this SDR Transmission 2 context, it identifies a separate camera-control path: the camera and TX exchange supported control data through an appropriate camera-control cable. DJI notes that some bodies need a USB setting such as PC Remote or PTP before the function appears. The Ronin app can then expose supported parameters. The exact cable, port and camera menu depend on the model; a random charging-only USB cable is not a useful substitute for a tested data connection.
One camera, two purposes
DJI says supported SDR Transmission 2 setups can adjust aperture, shutter speed and ISO, take photos, and start or stop recording. DJI quotes approximately 0.5–1 second for certain parameter changes depending on the camera system. This is a qualified control-response reference, not wireless-video latency. Focus and zoom are not included as universal PTP controls. For camera-menu mirroring, the PDF says some models require HDMI Info Display to be enabled. The DJI camera-control support article explains the general functions and limitations.
What DJI marks for popular camera bodies
This selection exposes the differences most likely to change a purchase or cable plan. It is intentionally not the entire manufacturer PDF. “Yes” means a checkmark in DJI's 1 September 2026 document; “—” means no checkmark in that cell. The latter is not a declaration of permanent incompatibility. The 4K and HD columns are camera-source monitoring results, not a promise that every output format will work.
On a phone, swipe within the table to see PTP and CEC.
| Camera | 4K video | HD video | PTP control | CEC mirror |
|---|---|---|---|---|
| Sony FX3 | Yes | Yes | Yes | Yes |
| Sony FX30 | Yes | Yes | Yes | — |
| Sony FX6 | Yes | Yes | — | — |
| Sony A7R V | Yes | Yes | Yes | Yes |
| Canon EOS R5 | Yes | Yes | Yes | — |
| Canon EOS R5 C | Yes | Yes | — | — |
| Canon EOS R6 Mark II | — | Yes | Yes | — |
| Nikon Z8 | Yes | Yes | Yes | — |
| Nikon Z9 | Yes | Yes | Yes | — |
| Panasonic LUMIX S5 IIX | Yes | Yes | Yes | — |
| Panasonic LUMIX GH6 | Yes | Yes | Yes | — |
| Fujifilm X-H2S | Yes | Yes | Yes | — |
| Fujifilm X-T30 | Yes | Yes | — | — |
Three patterns are useful: the FX3 is a documented all-four-column example; the FX30 and many other bodies add PTP without a CEC mark; and the FX6 is a marked video source without either control mark. The EOS R5 C makes the same point within Canon: similar names do not produce identical remote-control support. The complete PDF remains the source of truth for bodies not shown here.
FX3, FX30 and FX6 are not the same control workflow
Sony FX3 has checkmarks for 4K, HD, PTP and CEC, so it is the clearest example of the four layers in one row. DJI's combined camera-control support page uses Sony FX3 to illustrate a PC Remote connection for the original SDR Transmission generation; the separate SDR Transmission 2 matrix independently marks FX3 for PTP. Treat the menu example as orientation, then confirm the current FX3 menu, firmware and Gen 2 cable path on the actual rig instead of assuming old-generation instructions are automatically identical.
Sony FX30 has 4K, HD and PTP marks but no CEC mark. Sony FX6 has 4K and HD marks with PTP and CEC cells blank. If the crew only needs a viewing feed, all three are listed as video sources. If the crew expects remote exposure controls or Mirror Control, those missing marks change the plan. The PDF also lists A7R V with all four marks, showing that camera family names alone are not enough to infer the result.
Canon EOS R5 versus R5 C
DJI marks both for 4K and HD monitoring. EOS R5 has a PTP mark; EOS R5 C does not. EOS R5 Mark II also carries a PTP mark. That is why “the R5 family works” is too vague for a customer who needs remote ISO or recording control. Confirm the exact body name, and do not sell a control cable as a fix for a blank matrix cell.
Canon also has a less obvious video-column exception: EOS R6 Mark II and EOS R7 have HD and PTP marks, but the 4K column is blank in this DJI document. That does not prove that their hardware lacks 4K output. It means this particular DJI compatibility list has not marked 4K monitoring for those rows; verify the intended 4K signal path before treating it as a supported setup.
Nikon Z8 and Z9: video plus PTP, not a CEC promise
DJI marks Nikon Z8 and Z9 for 4K monitoring, HD monitoring and PTP camera control. Neither row carries a CEC mark. For a production team, that points toward a camera-control-cable and app-parameter plan when remote exposure matters, rather than assuming HDMI Mirror Control will be present.
Nikon Z6 III has the same 4K/HD/PTP pattern. Z7 II is a useful counterexample: its video columns are marked, but PTP and CEC are blank. Use the full matrix for other Nikon bodies and perform a pre-shoot check of the exact camera firmware and selected output format.
Fujifilm belongs in this compatibility decision
Panasonic LUMIX S5 II, S5 IIX, S9, S1 II and GH6 have 4K, HD and PTP marks in DJI's list; none of those selected rows has a CEC mark. LUMIX S1H has 4K and HD marks but a blank PTP cell. One unusual row, LUMIX S1 II E, has a PTP mark while both video-monitoring cells are blank. Do not infer a complete video-and-control workflow from that row without a direct confirmation or on-rig test.
Fujifilm X-H2S, X-T3, X-T4, X-T5, X-S10, X-S20 and GFX100 II all carry 4K, HD and PTP marks. X-T30 and X-T30 II carry video marks but no PTP mark. The Fujifilm rows in this document have no CEC marks. X-H2S is therefore a documented PTP-capable example, not a reason to promise HDMI mirroring on every Fuji body.
A 4K checkmark is not “every 4K format works”
The compatibility PDF identifies a tested 4K monitoring result, while the SDR Transmission 2 source-format specification identifies the formats the main-unit input accepts. DJI lists DCI and UHD 4K at 23.98, 24, 25, 29.97, 30, 50, 59.94 and 60 fps; 1080p uses those listed rates, while 1080i and 720p have narrower entries. A camera may offer output modes outside that list, and the monitor at the other end must accept the receiver's chosen output. Read the DJI SDR Transmission 2 User Manual and downloads for the current format table.
Start with the camera's clean, supported HDMI output and a simple TX/RX monitor path. If the feed is missing, check the camera's actual output resolution and frame rate, cable seating and RX monitor format before treating the camera as unsupported. The SpeedyDrone TX/RX setup and no-signal guide covers activation, roles, power, ports and Auto Channel; this page does not repeat that installation sequence.
A six-point test before a paid shoot
- Find the exact body row in DJI's current list, not just the brand or camera family.
- Separate picture from control: note the 4K, HD, PTP and CEC cells independently.
- Choose the camera-side connections: HDMI for the required video path; a suitable camera-control/data cable and the camera's PC Remote/PTP setting where supported.
- Set one known-good format that the camera, transmitter, receiver and monitor all accept.
- Test the functions you will actually use: ISO, shutter, aperture, photo/record trigger and mirror control only where marked, plus reconnect behaviour.
- Document the working settings for the crew and repeat the test after firmware, cable or camera-mode changes.
If the system is mounted on a Ronin stabilizer, gimbal power and movement control are another separate compatibility layer. The DJI RS 5 at SpeedyDrone uses the included USB-C firmware-update cable for its SDR 2 connection. The DJI RS 4 Pro and DJI RS 4 need the separately sold SDR Transmission 2 USB-C-to-CAN gimbal-control cable. DJI also lists RS 3 Pro, Ronin 2 and Master Wheels, with their own specified paths. See DJI's stabilizer connection guide before buying a cable; a gimbal connection does not turn a blank camera PTP row into a supported one.
Choose the link hardware after the camera test
For a new camera-to-monitor wireless link, plan one SDR Transmission 2 unit in TX mode and one in RX mode. The Combo supplies two switchable transceivers; a single-unit package is more useful as an extra receiver, a spare or a replacement within an existing Gen 2 setup. Neither package makes an unmarked camera-control function appear, and both still require the correct camera/monitor cables and operating power.
SpeedyDrone's public product pages showed backorder notices when checked on 19 September 2026, so these links are for configuration review—not a promise that equipment can arrive before a shoot. Contact the team to confirm the current ETA and the exact accessories for your camera. For a Gen 1-versus-Gen 2 purchase decision, read the separate SDR Transmission 2 upgrade comparison.
DJI SDR Transmission 2
One TX/RX-switchable unit. Add a viewing position or keep a spare; one unit alone cannot create both ends of a wireless link.
View DJI SDR Transmission 2 at SpeedyDrone →
DJI SDR Transmission 2 Combo
Two switchable units for a basic one-TX/one-RX link. Camera, monitor, operating batteries and the required video cables need separate planning.
View DJI SDR Transmission 2 Combo at SpeedyDrone →DJI SDR Transmission 2 camera compatibility FAQ
Is Sony FX3 compatible with DJI SDR Transmission 2?
Yes. DJI's 1 September 2026 camera list marks Sony FX3 for 4K video monitoring, 1080p/1080i monitoring, PTP camera control and CEC Mirror Control. Those are four separate tested columns, not a promise that every camera-output format or menu setting works without configuration. Use a supported video output for the picture and the required camera-control connection/settings for PTP. Test the complete TX/RX and display chain before a shoot.
Can DJI SDR Transmission 2 remotely control Sony FX3?
DJI marks FX3 for PTP and CEC in its Gen 2 camera matrix. Its combined camera-control support page describes aperture, shutter and ISO adjustment, photo and recording triggers for supported Gen 2 setups. The page also gives an FX3 PC Remote example in the original-generation section; treat that as orientation, not a guaranteed Gen 2 menu-by-menu procedure. Confirm the FX3's current firmware, camera-control cable and settings on the actual rig. Do not assume generic focus or zoom control.
Does Sony FX6 have the same control support as FX3?
No, not in DJI's current published matrix. FX6 has 4K and HD monitoring marks, while its PTP and CEC cells are blank. FX3 has all four marks. A blank cell should be read as “not marked in this DJI list,” rather than a claim about every conceivable firmware or third-party connection. For an FX6 production, plan the video-monitoring path from the documented marks and verify any separate camera-control solution on its own evidence.
Does Canon EOS R5 C have the same SDR 2 control support as EOS R5?
No. Both EOS R5 and EOS R5 C have 4K and HD monitoring marks. EOS R5 has a PTP camera-control mark; EOS R5 C does not have that mark in DJI's 1 September 2026 table. Neither of those rows is marked for CEC. The exact “C” body matters: do not transfer the R5 control result to R5 C simply because the names and HDMI-monitoring results look similar.
Do Nikon Z8 and Z9 support PTP control with SDR Transmission 2?
DJI marks both Nikon Z8 and Z9 for 4K monitoring, HD monitoring and PTP camera control. Their CEC cells are blank. To use PTP, DJI says the camera and transmitter need a camera-control cable, and some camera models require the proper PC Remote/PTP USB setting. Verify the Nikon model's current settings and test the controls you need in the Ronin app, not just the video feed.
Is Fujifilm X-H2S on the DJI SDR Transmission 2 compatibility list?
Yes. Fujifilm X-H2S has checkmarks for 4K monitoring, 1080p/1080i monitoring and PTP camera control in DJI's published list; its CEC cell is blank. Other Fujifilm models have different rows. X-T30, for example, has video-monitoring marks but no PTP mark. Check the exact camera body rather than assuming every Fujifilm model shares the X-H2S control result.
Does an HDMI picture automatically enable ISO, shutter and aperture control?
No. HDMI video and PTP parameter control are separate paths. A compatible HDMI output can deliver a picture even when the camera lacks a PTP mark or the camera-control cable and USB setting are missing. HDMI is also the path DJI specifies for CEC Mirror Control on marked cameras, but a video feed alone does not prove CEC is enabled. Read all four matrix columns and build the physical connections for the functions you intend to use.
Can SDR Transmission 2 control focus or zoom on every PTP-marked camera?
No. DJI's general SDR Transmission 2 camera-control description centres on aperture, shutter and ISO adjustment plus photo and start/stop recording triggers for supported setups. That description does not establish universal PTP focus or zoom control. DJI's FX3 example in the combined support page expressly excludes focus and zoom in that workflow. Treat lens-motor or gimbal focusing systems as separate equipment and compatibility questions, not an automatic consequence of a PTP checkmark.
Why is there no 4K mark for Canon EOS R6 Mark II in DJI's table?
DJI's 1 September 2026 PDF leaves the R6 Mark II 4K-monitoring cell blank while marking its HD monitoring and PTP columns. The document does not explain the reason, so this guide does not infer that the camera cannot output 4K or that every 4K setting will fail. For a 4K-dependent purchase, confirm the exact camera output mode against DJI's supported input formats and obtain a working test of your complete cable, TX, RX and display chain.
What was checked
DJI SDR Transmission 2 Camera Compatibility List (1 September 2026): every model cell in the curated matrix and the PTP/CEC connection footnotes.
DJI camera-control support: supported Gen 2 control functions and the original-generation FX3 example, kept separate in this article.
DJI SDR Transmission 2 downloads and user manual: accepted source formats and device documentation.
SpeedyDrone SDR Transmission 2 collection and the linked product pages: exact packages and the public backorder wording checked 19 September 2026. Recheck availability and the manufacturer matrix before publication or a time-critical purchase.
Check your exact camera and control goal before ordering.
Send SpeedyDrone your camera model and firmware, the video mode you plan to output, your monitor or mobile device, and whether you need PTP parameters, CEC mirroring or only a clean feed. We can help you compare the Single and Combo configurations and confirm the current backorder ETA.
Ask SpeedyDrone to review your setup →
